Topic 1: Deployment
Which Cisco Firepower Threat Defense, which two interface settings are required when configuring a routed interface? (Choose two.)
A. Redundant Interface
B. EtherChannel
C. Speed
D. Media Type
E. Duplex
Explanation
When configuring a physical interface as a routed interface on Cisco Firepower Threat Defense (FTD) through Firepower Management Center (FMC), the Hardware Configuration tab provides the settings used to configure physical link parameters. These include Speed and Duplex.
According to Cisco's FTD interface configuration documentation, the available hardware settings include:
Duplex: Select Full, Half, or Auto, which is the default setting where supported.
Speed: Select a supported speed, such as 10, 100, or 1000 Mbps, or Auto, depending on the platform and interface capabilities.
These settings help ensure that the physical interface negotiates correctly with the connected switch or router. In modern networks, Auto is commonly used when both ends support compatible auto-negotiation settings.
Why the Other Options Are Incorrect
Option A — Redundant Interface: A redundant interface is a logical interface that combines two physical interfaces for high availability. It is an alternative interface type rather than a hardware setting within an individual routed physical interface.
Option B — EtherChannel: An EtherChannel combines multiple physical links into a logical link for increased capacity and redundancy. It is a separate logical interface configuration, not a hardware parameter within a routed physical interface. Support depends on the FTD platform, software version, and operating mode; the relevant Cisco documentation should be consulted before making a universal claim about support.
Option D — Media Type: Media type can relate to the physical transmission medium or interface-specific options on supported hardware. However, it is not one of the standard Speed and Duplex settings identified in this question's routed-interface hardware configuration workflow.
Reference
Cisco Firepower Management Center Configuration Guide, interface configuration section covering the Hardware Configuration tab and physical interface Speed and Duplex settings.
What is a result of enabling Cisco FTD clustering?
A. For the dynamic routing feature, if the master unit fails, the newly elected master unit maintains all existing connections.
B. Integrated Routing and Bridging is supported on the master unit
C. Site-to-site VPN functionality is limited to the master unit, and all VPN connections are dropped if the master unit fails
D. Site-to-site VPN functionality is limited to the master unit, and all VPN connections are dropped if the master unit fails
Explanation
When you enable clustering on Cisco FTD, certain features are classified as centralized features. These features do not scale across the cluster; instead, they are handled exclusively by the control node (often referred to as the master unit in older documentation). Site-to-site VPN is one of these centralized features.
According to Cisco documentation, VPN functionality is limited to the control node and does not take advantage of the cluster's high availability capabilities. If the control node fails, all existing VPN connections are lost, and users will experience a disruption until a new control node is elected and the VPN connections are re-established.
Why the Other Options Are Incorrect
A. For the dynamic routing feature, if the master unit fails, the newly elected master unit maintains all existing connections: This is incorrect. While dynamic routing is a centralized feature, the OSPF LSA database is not synchronized from the control node to data nodes. If a control node switchover occurs, the neighboring router will detect a restart, and the switchover is not transparent. The routing process runs only on the control node, and routes are learned through it and replicated to data nodes.
B. Integrated Routing and Bridging is supported on the master unit: This is incorrect. Integrated Routing and Bridging (IRB) is explicitly listed as a feature that is not supported with clustering. It cannot be configured when clustering is enabled.
D. All Firepower appliances can support Cisco FTD clustering: This is incorrect. Clustering is not supported on all Firepower appliances. It is limited to specific hardware platforms, primarily the Firepower 4100 and Firepower 9300 series (and newer platforms like the Secure Firewall 3100). Many lower-end or virtual appliances do not support clustering.
Reference
Cisco Firepower Management Center Configuration Guide: Under the "VPN and Clustering" section, it states that site-to-site VPN is a centralized feature, only the control node supports VPN connections, and if the control node fails, all existing VPN connections are lost.
An engineer is tasked with deploying an internal perimeter firewall that will support multiple DMZs Each DMZ has a unique private IP subnet range. How is this requirement satisfied?
A. Deploy the firewall in transparent mode with access control policies
B. Deploy the firewall in routed mode with access control policies.
C. Deploy the firewall in routed mode with NAT configured.
D. Deploy the firewall in transparent mode with NAT configured.
Explanation
The key detail is that each DMZ has its own unique private IP subnet. A firewall that connects multiple distinct Layer 3 subnets has to route between them, so it must run in routed mode. In routed mode, each interface is assigned an IP address in its own subnet and acts as the default gateway for the hosts in that DMZ. Traffic between DMZs, and between the DMZs and the internal or outside networks, is then permitted or denied by < access control policies, which is what actually enforces the perimeter security between the zones.
Why the other options are wrong
A. Transparent mode with access control policies: Transparent mode (a “bump in the wire”) makes the firewall act as a Layer 2 device. It bridges interfaces within the same subnet and doesn’t route between different IP subnets, so it doesn’t fit multiple DMZs with unique subnets.
C. Routed mode with NAT configured: Routed mode is correct, but NAT isn’t required to separate or support multiple private subnets. NAT translates addresses, typically for Internet access or overlapping address space, and the question doesn’t ask for translation. Access control policies are what satisfy the segmentation requirement.
D. Transparent mode with NAT configured: Wrong on the mode for the same reason as A. NAT also isn’t the requirement here.
Reference
Cisco Secure Firewall Management Center (FMC) Device Configuration Guide: Transparent or Routed Firewall Mode for Firewall Threat Defense and Regular Firewall Interfaces (routed interface configuration).
Which two dynamic routing protocols are supported in Firepower Threat Defense without using FlexConfig? (Choose two.)
A. EIGRP
B. OSPF
C. static routing
D. IS-IS
E. BGP
Explanation
In Cisco Firepower Threat Defense (FTD) managed by Firepower Management Center (FMC), OSPF and BGP are the two dynamic routing protocols that can be configured natively through the FMC device routing interface without requiring FlexConfig. The FMC configuration guide lists dedicated chapters for OSPF and BGP configuration, confirming they are first-class supported features in the management UI.
Why the Other Options Are Incorrect
A. EIGRP: Although the underlying FTD software can run EIGRP, FMC does not expose it as a native routing option. Configuring EIGRP requires using FlexConfig objects (such as `Eigrp_Configure` and `Eigrp_Interface_Configure`) to push CLI commands to the device.
C. Static routing: Static routes are indeed supported natively in FMC, but the question specifically asks for dynamic routing protocols. Static routing is manually configured and does not dynamically exchange routes with neighbors.
D. IS-IS: Similar to EIGRP, IS-IS is not available as a native routing configuration in FMC. It must be deployed through FlexConfig using predefined objects like `ISIS_Configure` and `ISIS_Interface_Configuration`.
Reference
Cisco Firepower Management Center Device Configuration Guide: The table of contents explicitly lists OSPF and BGP as native routing chapters, while the FlexConfig predefined objects section includes `Eigrp_Configure` and `ISIS_Configure` for protocols that require CLI injection.
Which two conditions are necessary for high availability to function between two Cisco FTD devices? (Choose two.)
A. The units must be the same version
B. Both devices can be part of a different group that must be in the same domain when configured within the FMC.
C. The units must be different models if they are part of the same series
D. The units must be configured only for firewall routed mode.
E. The units must be the same model.
Explanation
Cisco FTD high availability (failover) has strict hardware and software consistency requirements. According to the official Cisco configuration guide, the two devices in an HA pair must meet the following conditions: the hardware models must be identical, and the software versions must be exactly the same (major, minor, and maintenance version numbers must all match). These are hard requirements for establishing the HA relationship; if the versions do not match, configuration synchronization will fail and failover will not function properly.
Why the Other Options Are Incorrect
B. Both devices can be part of a different group that must be in the same domain: This is incorrect. The two devices must be in the same domain or group within FMC, not in different groups.
C. The units must be different models if they are part of the same series: This is incorrect. The requirement is the exact opposite—the models must be identical, and different models cannot form an HA pair.
D. The units must be configured only for firewall routed mode: This is incorrect. FTD HA supports both routed and transparent modes; it does not require routed mode only. The actual requirement is that both devices must be in the same firewall mode (both routed or both transparent).
Reference
Cisco Secure Firewall Management Center Device Configuration Guide, 7.4 — High Availability: Hardware Requirements and Software Requirements sections list "same model" and "same software version" as mandatory conditions.
A network security engineer must replace a faulty Cisco FTD device in a high availability pair. Which action must be taken while replacing the faulty unit?
A. Shut down the Cisco FMC before powering up the replacement unit.
B. Ensure that the faulty Cisco FTD device remains registered to the Cisco FMC.
C. Unregister the faulty Cisco FTD device from the Cisco FMC
D. Shut down the active Cisco FTD device before powering up the replacement unit.
Explanation
When replacing a faulty unit in an FTD high availability (HA) pair, Cisco's official RMA (Return Merchandise Authorization) procedure explicitly instructs: do not unregister the faulty device from the FMC, even when disconnecting it from the network. Furthermore, you should not suspend or break the HA relationship during the replacement process. Maintaining these management and HA links ensures that the replacement device can automatically reconnect and rejoin the HA pair after the backup is restored.
The replacement unit is restored from a backup taken of the faulty device. After the restore completes, the replacement device reboots and automatically connects to the FMC, appearing as the original device. If the faulty unit had been unregistered, this automatic reconnection and HA synchronization would fail.
Why the Other Options Are Incorrect
A. Shut down the Cisco FMC before powering up the replacement unit: There is no requirement to shut down the FMC. The FMC must remain operational to manage the HA pair and facilitate the replacement process.
C. Unregister the faulty Cisco FTD device from the Cisco FMC: This directly contradicts Cisco's explicit instruction. Unregistering the device breaks the management link needed for the replacement to automatically reconnect and resume HA synchronization.
D. Shut down the active Cisco FTD device before powering up the replacement unit: This would cause an unnecessary outage. The active unit should remain operational to maintain network availability while the faulty standby unit is replaced.
Reference
Cisco Firepower Management Center Configuration Guide — Backup and Restore: "Do not unregister from the FMC, even when disconnecting a device from the network. In an FTD HA deployment, do not suspend or break high availability. Maintaining these links ensures replacement devices can automatically reconnect after restore."
An engineer is building a new access control policy using Cisco FMC. The policy must inspect a unique IPS policy as well as log rule matching. Which action must be taken to meet these requirements?
A. Configure an IPS policy and enable per-rule logging
B. Disable the default IPS policy and enable global logging.
C. Configure an IPS policy and enable global logging
D. Disable the default IPS policy and enable per-rule logging
Explanation
In Cisco FMC, the requirement to "inspect a unique IPS policy" means you must attach an intrusion policy to the specific access control rule that handles the traffic. The requirement to "log rule matching" means you must enable logging on that specific access control rule itself (per-rule logging), so that connections matching the rule generate connection events. These are two distinct configurations: the IPS policy is assigned within the rule's Inspection tab, while logging is enabled within the rule's Logging tab.
Why the Other Options Are Incorrect
B. Disable the default IPS policy and enable global logging: Disabling the default policy does not satisfy the requirement for a unique IPS policy, and global logging (set at the policy level) does not provide the granular per-rule logging requested.
C. Configure an IPS policy and enable global logging: While an IPS policy is configured, global logging applies defaults to the entire policy. The requirement specifically asks to log rule matching, which is achieved through per-rule settings, not a global default.
D. Disable the default IPS policy and enable per-rule logging: This fails because it removes IPS inspection entirely; the requirement explicitly demands inspection with a unique IPS policy.
Reference
Cisco Secure Firewall Management Center Device Configuration Guide: Access control rules contain an Inspection tab for assigning an intrusion (IPS) policy and a Logging tab for configuring per-rule connection logging.
An engineer is configuring a Cisco IPS to protect the network and wants to test a policy
before deploying it. A copy of each incoming packet needs to be monitored while traffic flow
remains constant. Which IPS mode should be implemented to meet these requirements?
A.
Inline tap
B.
passive
C.
transparent
D.
routed
Inline tap
Explanation
The question requires "a copy of each incoming packet needs to be monitored" while "traffic flow remains constant." This is exactly the definition of Inline Tap mode in Cisco FTD.
With Tap mode enabled on an inline set, the device is deployed inline (cabling is in the traffic path), but the actual traffic is bridged internally and forwarded unmodified. A copy of each packet is sent to the Snort inspection engine for analysis. Because the real traffic is not actually passed through the inspection engine, the flow is undisturbed and the device cannot drop packets based on inspection results—drop rules only generate events indicating what *would* have happened. This makes it ideal for testing an IPS policy before putting it into blocking mode.
Why the Other Options Are Incorrect
B. passive: A passive interface receives a copy of traffic from a SPAN/mirror port on a switch, but the FTD itself is not deployed inline in the traffic path. While traffic flow is undisturbed, the scenario implies the device is cabled inline (ready to transition to blocking later). Inline tap is the specific FTD feature designed for "inline deployment with copy-only inspection."
C. transparent: Transparent mode is a firewall deployment mode (Layer 2 bridge), not an IPS inspection mode. In transparent mode, the FTD actively forwards traffic and *can* drop packets via access control—traffic does not remain "constant" in the sense of being uninfluenced by policy drops.
D. routed: Routed mode is a Layer 3 firewall deployment. The FTD acts as a gateway, performs routing, and can drop traffic. It does not meet the "monitor a copy while traffic flow remains constant" requirement.
Reference
Cisco Firepower Management Center Configuration Guide: Under Inline Set Advanced settings, "Tap Mode—Set to inline tap mode." Cisco documentation states: "With tap mode, the device is deployed inline, but instead of the packet flow passing through the device, a copy of each packet is sent to the device and the network traffic flow is undisturbed."
An engineer must configure high availability for the Cisco Firepower devices. The current network topology does not allow for two devices to pass traffic concurrently. How must the devices be implemented in this environment?
A. in active/active mode
B. in a cluster span EtherChannel
C. in active/passive mode
D. in cluster interface mode
Explanation
Cisco FTD high availability (failover) is designed so that only one unit actively passes traffic at a time. In active/passive mode, the active unit forwards traffic while the standby unit does not actively pass traffic; it only synchronizes configuration and state information from the active unit and takes over if the active unit fails. This directly matches the constraint that the topology does not allow two devices to pass traffic concurrently.
Why the Other Options Are Incorrect
- A. in active/active mode: Cisco FTD high availability does not support active/active failover. Active/active is an ASA feature (using multiple contexts), not an FTD HA mode.
- B. in a cluster span EtherChannel: Clustering is a separate scalability technology, not an HA failover mode, and it is not the standard solution for the stated topology limitation.
- D. in cluster interface mode: This is not a valid FTD HA mode. Clustering uses a control unit and data units, but the question asks about high availability for two Firepower devices under a no-concurrent-traffic constraint.
Reference
Cisco Secure Firewall Management Center Device Configuration Guide, 7.4 — High Availability: "Threat Defense supports Active/Standby failover, where one unit is the active unit and passes traffic. The standby unit does not actively pass traffic, but synchronizes configuration and other state information from the active unit."
A network engineer implements a new Cisco Firepower device on the network to take advantage of its intrusion detection functionality. There is a requirement to analyze the traffic going across the device, alert on any malicious traffic, and appear as a bump in the wire How should this be implemented?
A. Specify the BVl IP address as the default gateway for connected devices.
B. Enable routing on the Cisco Firepower
C. Add an IP address to the physical Cisco Firepower interfaces.
D. Configure a bridge group in transparent mode.
Explanation
The key requirements are "intrusion detection" and "appears as a bump in the wire." In Cisco FTD, transparent mode is the deployment mode that functions as a Layer 2 firewall. It does not perform routing and is invisible to connected devices, which is precisely the "bump in the wire" effect. In transparent mode, data interfaces must be added to a bridge group, and the device forwards traffic through Layer 2 bridging based on MAC address lookups. Meanwhile, access control policies can be applied to the member interfaces of the bridge group to implement intrusion detection and alerting.
Why the Other Options Are Incorrect
A. Specify the BVI IP address as the default gateway for connected devices: This is incorrect. Cisco official documentation explicitly states that in transparent mode, the BVI IP address should not be specified as the default gateway for connected devices; devices should specify the router on the other side of the FTD as their gateway.
B. Enable routing on the Cisco Firepower: This is incorrect. Enabling routing means deploying in routed mode, where the device performs Layer 3 forwarding and IP addresses need to be configured on interfaces, which no longer maintains the "bump in the wire" characteristic.
C. Add an IP address to the physical Cisco Firepower interfaces: This is incorrect. In transparent mode bridge groups, member interfaces do not configure IP addresses; only the BVI (Bridge Virtual Interface) needs an IP address.
Reference
Cisco Firepower Management Center Configuration Guide: In transparent mode, data interfaces must belong to a bridge group, and traffic within the bridge group is forwarded based on destination MAC address lookups rather than routing lookups. Cisco Learning Network also confirms that both transparent mode and inline mode exhibit "bump in the wire" behavior.
What are two application layer preprocessors? (Choose two.)
A. CIFS
B. IMAP
C. SSL
D. DNP3
E. ICMP
Explanation
In Cisco Firepower's network analysis policy (NAP), Application Layer Preprocessors are protocol decoders that normalize application-layer traffic so the intrusion rules engine can analyze it consistently. Cisco documentation categorizes IMAP and SSL as application layer preprocessors. The IMAP preprocessor decodes IMAP traffic to detect anomalies, while the SSL preprocessor handles encrypted session inspection and identifies encrypted traffic to reduce false positives.
Why the Other Options Are Incorrect
A. CIFS: Not listed as an application layer preprocessor. Cisco's application layer section covers DCE/RPC (which includes SMB/Samba processing) but not CIFS as a separate preprocessor.
D. DNP3: This is a SCADA preprocessor, not an application layer preprocessor. Cisco documentation categorizes DNP3, Modbus, CIP, and S7Commplus under SCADA preprocessors separately from application layer preprocessors.
E. ICMP: This is a network layer protocol handled by transport/network layer preprocessing, not an application layer preprocessor.
Reference
Cisco FireSIGHT System User Guide — Application Layer Preprocessors: The section explicitly lists IMAP, POP, SMTP, SSH, and SSL as application layer preprocessors, while DNP3 is documented under SCADA preprocessing.
An organization is migrating their Cisco ASA devices running in multicontext mode to Cisco FTD devices. Which action must be taken to ensure that each context on the Cisco ASA is logically separated in the Cisco FTD devices?
A. Add a native instance to distribute traffic to each Cisco FTD context
B. Add the Cisco FTD device to the Cisco ASA port channels
C. Configure a container instance in the Cisco FTD for each context in the Cisco ASA
D. Configure the Cisco FTD to use port channels spanning multiple networks
Explanation
The multi-context mode of the Cisco ASA implements logical isolation by partitioning a single application instance. On Cisco FTD, the equivalent capability is the multi-instance feature, which is implemented through container instances. Cisco official documentation explicitly states that multi-instance capability is similar to ASA multi-context mode, but the implementation differs: container instances provide hard resource isolation, independent configuration management, independent restart, and independent software upgrades, thereby logically separating each original ASA context on the FTD.
Why the Other Options Are Incorrect
A. Add a native instance to distribute traffic to each Cisco FTD context: Incorrect. A native instance occupies all CPU, RAM, and disk resources of the entire security module or engine. Only one native instance can be installed, so it cannot allocate a separate instance for each context.
B. Add the Cisco FTD device to the Cisco ASA port channels: Incorrect. Port channels are an interface-level link aggregation technology and are unrelated to logical isolation between contexts.
D. Configure the Cisco FTD to use port channels spanning multiple networks: Incorrect. This option similarly addresses only interface-level configuration and cannot implement separate logical partitions for each ASA context on the FTD.
Reference
Cisco official documentation, "Logical Device Application Instances: Container and Native," states that multi-instance capability is similar to ASA multiple-context mode. Container instances provide hard resource separation, separate configuration management, independent reloads, and separate software updates.
| Page 1 out of 35 Pages |
| 1234567891011 |
The Cisco 300-710 SNCF (Securing Networks with Cisco Firewalls) exam evaluates your ability to deploy, configure, manage, and troubleshoot Cisco Secure Firewall solutions, formerly known as Cisco Firepower. Understanding the official exam blueprint and practicing configuration-based scenarios are essential for effective preparation.
Exam Code: 300-710 SNCF
Exam Version: v1.2
Duration: 90 minutes
Certification: CCNP Security Concentration
Exam Focus: Cisco Secure Firewall and Secure Firewall Management Center
Cisco divides the SNCF exam into four major domains:
| Exam Domain | Weightage |
|---|---|
| Deployment | 30% |
| Configuration | 30% |
| Management and Troubleshooting | 25% |
| Integration | 15% |
Study firewall deployment modes and network availability solutions.
Routed and transparent firewall modes
NGIPS passive and inline deployment
High availability, failover, and clustering
ECMP routing and static route tracking
Virtual firewall management in cloud and on-premises environments
Preparation Tip: Understand how deployment modes affect traffic inspection, routing, and network resilience.
This domain tests practical configuration skills using Cisco Secure Firewall Management Center.
Access control, DNS, and identity policies
Network discovery and application detection
NAT, QoS, routing, and VPN configuration
Intrusion rules and Snort functionality
Encrypted Visibility Engine and security objects
Preparation Tip: Focus on firewall policy behavior, rule evaluation, and troubleshooting incorrect configurations.
Learn how to monitor firewall operations and diagnose security problems.
Firewall Management Center GUI and CLI
Packet capture and Packet Tracer
Firewall engine debugging and System Support Trace
Security dashboards, event logs, and reporting
Firewall management tools and monitoring
Preparation Tip: Practice identifying why legitimate traffic is blocked and interpreting firewall events.
Understand how Cisco Secure Firewall integrates with other security technologies.
Cisco Secure Endpoint and Malware Defense
Threat Intelligence Director
Cisco XDR security investigations
pxGrid and Rapid Threat Containment
Splunk integration and security analytics
Preparation Tip: Learn the purpose of each integration and how it improves threat detection and response.
Deployment and Configuration together represent 60% of the exam. Prioritize firewall modes, high availability, security policies, NAT, and VPN configurations.
Next, strengthen troubleshooting skills through packet analysis, event interpretation, and diagnostic tools.
Cistified provides free Cisco 300-710 SNCF practice questions and paid mock tests to support your preparation.
Test your understanding of major exam objectives.
Identify weak areas before your exam.
Practice applying firewall concepts to realistic scenarios.
Improve question-solving speed and time management.
Build confidence through repeated mock exam practice.
Combine Cisco's official study resources with hands-on firewall practice and regular knowledge assessments. Review your incorrect answers, concentrate on high-weightage domains, and use Cistified practice tests to evaluate your readiness before exam day.
Real-World Scenario Mastery: Our 300-710 practice exam don't just test definitions. They present you with the same complex, scenario-based problems you'll encounter on the actual exam.
Strategic Weakness Identification: Each practice session reveals exactly where you stand. Discover which domains need more attention, before Securing Networks with Cisco Firepower (300-710 SNCF) exam day arrives.
Confidence Through Familiarity: There's no substitute for knowing what to expect. When you've worked through our comprehensive 300-710 practice exam questions pool covering all topics, the real exam feels like just another practice session.