Free 300-710 Practice Test Questions 2026

420 Questions


Last Updated On : 18-Nov-2026


Topic 3: Management and Troubleshooting

How many report templates does the Cisco Firepower Management Center support?


A.

20


B.

10


C.

5


D.

unlimited





D.
  

unlimited



Explanation:

According to Cisco's official documentation for the Firepower Management Center, there is no fixed limit on the number of report templates you can create. The system provides a flexible reporting framework, and administrators can create as many templates as needed to meet their organization's requirements.

Why the Other Options Are Incorrect:

A. 20, B. 10, C. 5: These specific numerical limits are not mentioned anywhere in the official Cisco documentation regarding report template creation. The system is designed to be scalable and does not impose such restrictions on the number of templates.

Reference:

Cisco Documentation: "Firepower Management Center Configuration Guide" – Section on Report Templates, which states that report templates can be created as needed without a specified maximum limit.

Which command should be used on the Cisco FTD CLI to capture all the packets that hit an interface?


A. configure coredump packet-engine enable


B. capture-traffic


C. capture


D. capture WORD





B.
  capture-traffic

Explanation:

On the Cisco Firepower Threat Defense (FTD) CLI, the capture-traffic command is the built-in utility used to capture packets seen by a network interface. This command invokes a tcpdump-based capture directly from the FTD CLI .

When you enter capture-traffic, the system first prompts you to select the domain (interface) from which you want to capture traffic, such as eth0, management interfaces, or a Global domain. After selecting the interface, you are prompted to specify the desired tcpdump options, such as setting the snaplength (-s), limiting the number of packets (-c), or applying Berkeley Packet Filter (BPF) syntax to restrict the capture to specific hosts, ports, or VLANs . This tool is specifically designed for capturing traffic on the FTD platform and is the recommended method for troubleshooting data plane issues at the interface level.

Why the Other Options Are Incorrect:

A. configure coredump packet-engine enable:
This is not a valid packet capture command. Coredump configuration is used for generating diagnostic crash files for the packet engine, not for capturing live traffic.

C. capture:
While capture is a valid command on FTD, it is used for configuring data plane capture sessions (e.g., capture CAPNAME interface INSIDE match ip host ...) to inspect traffic that traverses the LINA engine, often for checking drops or detailed traces . The question specifically asks for the command to capture all packets that hit an interface, and capture-traffic is the dedicated interface-level tcpdump utility.

D. capture WORD:
This is an incomplete syntax. The capture command requires a capture name and interface specification, and it is not the primary tool for capturing raw traffic on an interface like capture-traffic is.

Reference:

Cisco Documentation: "Use Packet Capture Procedures on Firepower Device" – Section on using the capture-traffic command in versions 6.1 and later .

A network administrator notices that remote access VPN users are not reachable from inside the network. It is determined that routing is configured correctly, however return traffic is entering the firewall but not leaving it What is the reason for this issue?


A. A manual NAT exemption rule does not exist at the top of the NAT table.


B. An external NAT IP address is not configured.


C. An external NAT IP address is configured to match the wrong interface.


D. An object NAT exemption rule does not exist at the top of the NAT table.





A.
  A manual NAT exemption rule does not exist at the top of the NAT table.

Explanation:

On Cisco Firepower Threat Defense (FTD), when remote access VPN users cannot reach internal resources despite correct routing, the issue is almost always related to NAT (Network Address Translation) processing order. The firewall receives the return traffic from the internal network, but before it can send it back to the VPN client, it applies NAT rules. If a dynamic NAT/PAT rule (such as the default "hide NAT" for internet access) catches the traffic first, the source IP of the return packet gets translated to the firewall's interface IP. The VPN client will drop this packet because it is not destined to its assigned VPN pool IP.

To fix this, you must create a Manual NAT Exemption rule (Identity NAT) and place it at the top of the NAT table (before any dynamic PAT rules) . This rule tells the firewall: "If traffic is going from the VPN pool to the internal network (or vice versa), do not translate the IP addresses." Because manual NAT rules are processed in order, placing it at the top ensures it is evaluated before the generic interface PAT rule that would otherwise break the return path .

Why the Other Options Are Incorrect:

B. An external NAT IP address is not configured:
If an external NAT IP were missing, the VPN tunnel itself likely would not establish, or the firewall would not be reachable from the outside. The scenario states routing is correct, implying the tunnel is up and basic connectivity exists.

C. An external NAT IP address is configured to match the wrong interface:
This would typically cause issues with the initial VPN connection or general internet access, not specifically the return path from inside to the VPN pool.

D. An object NAT exemption rule does not exist at the top of the NAT table:
Object NAT rules (Auto NAT) are processed after Manual NAT rules. While an object NAT exemption could work, the standard Cisco best practice and documentation specifically recommend using a Manual NAT rule placed at the top to guarantee it is evaluated before the default dynamic PAT rule . Therefore, "Manual NAT" is the more precise and recommended answer.

Reference:

Cisco Support Documentation: "Configure Internal Resource Access for VPN Users on FTD with HairPin NAT" — explicitly states the need for a NAT Exemption rule (Manual NAT) for VPN Pool to Internal Subnet .

Which two features of Cisco AMP for Endpoints allow for an uploaded file to be blocked? (Choose two.)


A. application blocking


B. simple custom detection


C. file repository


D. exclusions


E. application whitelisting





A.
  application blocking

B.
  simple custom detection

Explanation

In Cisco AMP for Endpoints, blocking a specific uploaded file can be achieved through different mechanisms depending on the intended outcome.

B. Simple Custom Detection allows administrators to create a list of specific files identified by their SHA-256 hashes. When the file hash is added to the list and the appropriate policy is applied, the AMP connector can detect and block the file according to the configured policy. This is a direct method for blocking a known malicious file on an endpoint.

A. Application Blocking is a feature under Outbreak Control in AMP for Endpoints. It allows administrators to prevent specified applications or executables from running based on the configured policy. If the uploaded file is an executable, application blocking can prevent it from executing on the endpoint.

Why the Other Options Are Incorrect

C. File repository: The file repository is used to store and manage files for analysis or archival purposes. It is not the primary feature for actively blocking files on endpoints.

D. Exclusions: Exclusions tell AMP to ignore specified files, paths, or other items for applicable detection purposes. They are not intended to block files.

E. Application whitelisting: Whitelisting, or Allowed Applications, is designed to permit approved applications. Although it may prevent unapproved applications from running when configured accordingly, it is an allow-list approach rather than the direct block-list method used to target a specific file hash.

Reference

Cisco documentation: "Configure a Simple Custom Detection List on the AMP for Endpoints Portal" — describes using SHA-256 hash lists to detect and block specific files according to the applicable policy.

What is a valid Cisco AMP file disposition?


A. non-malicious


B. malware


C. known-good


D. pristine





B.
  malware

b>Explanation

Cisco AMP for Endpoints uses file dispositions to categorize files based on their SHA-256 hashes and available threat intelligence. These dispositions help the AMP connector determine how to handle files according to their classification and the configured policy.

Common file dispositions include Malware (confirmed malicious), Clean (verified safe), Unknown (not yet classified), and Unverified (not fully analyzed). Other statuses, such as Custom Detection and Quarantined, describe files that match custom detection criteria or have been isolated by the system.

Therefore, Malware is the valid file disposition among the given choices.

Why the Other Options Are Incorrect

A. Non-malicious: This is not the standard disposition name used to identify a safe file in AMP. The corresponding disposition is Clean.

C. Known-good: This is a general industry term for a trusted file, but the standard AMP disposition is Clean.

D. Pristine: This term may be used in other threat intelligence contexts, but it is not the standard file disposition expected in this question.

Reference

Cisco AMP for Endpoints User Guide — see the section on file dispositions and malicious file handling for the terminology used to classify files.

An engineer is configuring Cisco FMC and wants to allow multiple physical interfaces to be part of the same VLAN. The managed devices must be able to perform Layer 2 switching between interfaces, including sub-interfaces. What must be configured to meet these requirements?


A. interface-based VLAN switching


B. inter-chassis clustering VLAN


C. integrated routing and bridging


D. Cisco ISE Security Group Tag





A.
  interface-based VLAN switching

Explanation

On Cisco Firepower Management Center (FMC), to allow multiple physical interfaces and their subinterfaces on a managed device to participate in the same Layer 2 broadcast domain, you must configure a Bridge Group.

On a Cisco FTD device managed by FMC, a Bridge Group combines multiple interfaces and subinterfaces into a single Layer 2 broadcast domain. The device can then switch traffic between the interfaces assigned to that group without requiring Layer 3 routing between them. This allows traffic to pass between connected ports within the same bridged network. This functionality is provided through Bridge Group configuration, also described in the context of interface-based VLAN switching.

Why the Other Options Are Incorrect

B. Inter-chassis clustering VLAN: This is used in FTD clustering to carry cluster-related traffic between chassis. It does not provide general Layer 2 switching between physical interfaces and subinterfaces on a single device.

C. Integrated routing and bridging: Integrated routing and bridging combines Layer 2 bridging with Layer 3 routing. However, the primary requirement here is to switch traffic between multiple interfaces within the same Layer 2 broadcast domain, which is achieved by configuring a Bridge Group.

D. Cisco ISE Security Group Tag: A Security Group Tag (SGT) supports identity-based segmentation through Cisco TrustSec. It does not provide Layer 2 VLAN switching between interfaces.

Reference

Cisco Firepower Management Center Configuration Guide — see the sections on Bridge Group Interfaces and interface-based VLAN switching for details about Layer 2 bridging on managed FTD devices.

Which two remediation options are available when Cisco FMC is integrated with Cisco ISE? (Choose two.)


A. dynamic null route configured


B. DHCP pool disablement


C. quarantine


D. port shutdown


E. host shutdown





C.
  quarantine

D.
  port shutdown

Explanation

When Cisco Firepower Management Center (FMC) integrates with Cisco Identity Services Engine (ISE), the two systems share threat and endpoint information to support network access control. When FMC identifies a compromised endpoint, remediation actions can be initiated through ISE to restrict the endpoint's network access.

C. Quarantine: ISE can quarantine an endpoint by changing its authorization policy, such as assigning a restrictive Security Group Tag (SGT), applying an access control policy, or placing the endpoint in a remediation VLAN. This limits network access until the threat is resolved and is a common remediation approach.

D. Port shutdown: ISE can use the supported capabilities of the network access device, such as a switch, to shut down the port connected to a compromised endpoint. This isolates the endpoint at the network level and prevents communication through that port.

Why the Other Options Are Incorrect

A. Dynamic null route configured: A null route can discard traffic, but modifying routing tables is not a standard endpoint remediation action in the FMC-ISE integration. Remediation typically uses network access controls, such as quarantine or port shutdown.

B. DHCP pool disablement: Disabling a DHCP pool could affect multiple devices using that pool rather than isolating only the compromised endpoint. It is not a targeted remediation action in this integration.

E. Host shutdown: FMC and ISE remediation actions primarily control network access. They do not directly shut down the endpoint's operating system through the standard remediation workflow.

Reference

Cisco Firepower Management Center and Cisco ISE Integration Guide — see the documentation on remediation actions, including quarantine and port shutdown. Availability depends on the supported integration version and network access device capabilities.

What is the maximum SHA level of filtering that Threat Intelligence Director supports?


A. SHA-1024


B. SHA-4096


C. SHA-512


D. SHA-256





D.
  SHA-256

Explanation

Cisco Threat Intelligence Director (TID) supports filtering and taking action based on SHA-256 hash values. According to Cisco documentation, TID extends Firepower's threat filtering capabilities by supporting SHA-256 file hashes in addition to IP addresses, URLs, and domain names.

When TID ingests threat intelligence feeds, SHA-256 is the supported observable type for file hashes in this context. The system uses these hash values to identify matching files and can trigger actions, such as monitoring or blocking, according to the configured policy.

Why the Other Options Are Incorrect

A. SHA-1024: This is not a standard cryptographic hash algorithm supported by TID. SHA-1024 is not a recognized SHA hash function in this context.

B. SHA-4096: This is not a standard SHA hash algorithm used by TID. The SHA-4096 designation does not correspond to a recognized SHA hash function for this purpose.

C. SHA-512: SHA-512 is a valid cryptographic hash algorithm, but the TID file-hash observable described in the question uses SHA-256.

Reference

Cisco documentation: "Cisco Threat Intelligence Director" — see the sections on supported observables and filtering criteria, which describe support for SHA-256 hash values.

Which Cisco Firepower rule action displays an HTTP warning page?


A. Monitor


B. Block


C. Interactive Block


D. Allow with Warning





C.
  Interactive Block

Explanation

In Cisco Firepower, the Interactive Block action is designed to display a customizable warning or response page when a user attempts to access traffic that matches an Interactive Block rule. Instead of simply dropping the connection, the system can present an HTTP response page explaining that the traffic is blocked and, depending on the configuration, allow the user to proceed for a specified period.

This action is useful in URL filtering and application control policies when administrators want to inform users about restricted content while maintaining visibility and control over access. The exact behavior depends on the rule configuration and the supported response-page settings.

Why the Other Options Are Incorrect

A. Monitor: This action allows matching traffic while logging it for analysis. It does not block the traffic or display an Interactive Block response page.

B. Block: This action prevents matching traffic from proceeding. Unlike Interactive Block, it does not provide the same interactive warning-page experience that may allow users to proceed.

D. Allow with Warning: This is not the standard access control rule action described for this behavior in Cisco FMC. The relevant action is Interactive Block, which provides the configured response-page behavior.

Reference

Cisco Firepower Management Center Configuration Guide — see the sections on access control rule actions, Interactive Block, and associated HTTP response pages.

In a Cisco AMP for Networks deployment, which disposition is returned if the cloud cannot be reached?


A. unavailable


B. unknown


C. clean


D. disconnected





A.
  unavailable

Explanation

In a Cisco AMP for Networks deployment, if the system attempts to query the AMP cloud for a file's disposition but cannot reach the cloud because of a network connectivity issue, the resulting disposition is Unavailable. Cisco documentation defines this state as indicating that the system could not query the AMP cloud.

This is different from Unknown, which means the cloud was successfully queried but the file has not yet been categorized. Therefore, Unavailable is the correct answer when the system cannot communicate with the AMP cloud.

Why the Other Options Are Incorrect

B. Unknown: This disposition means the AMP cloud was queried successfully, but the file has not yet received a classification. It does not indicate a cloud connectivity failure.

C. Clean: This disposition indicates that the AMP cloud has classified the file as safe. A successful cloud lookup is required to obtain this classification.

D. Disconnected: This is not a standard file disposition in the AMP for Networks context. Although it describes a connection state, it is not the disposition assigned when the AMP cloud cannot be queried.

Reference

Cisco Firepower Management Center Configuration Guide — File Disposition definitions: "Unavailable indicates that the system could not query the AMP cloud."

Which action should you take when Cisco Threat Response notifies you that AMP has identified a file as malware?


A. Add the malicious file to the block list


B. Send a snapshot to Cisco for technical support


C. Forward the result of the investigation to an external threat-analysis engine


D. Wait for Cisco Threat Response to automatically block the malware





A.
  Add the malicious file to the block list

Explanation

When Cisco Threat Response (CTR) notifies you that Cisco AMP has identified a file as malware, an appropriate remediation action is to add the file's SHA-256 hash to the Custom Detections block list in AMP for Endpoints. Once the list and applicable policy are configured and deployed, AMP can detect and block the identified file across managed endpoints according to the policy settings. Depending on the configuration, the connector may also quarantine the file. Threat Response helps security analysts investigate threats and initiate response actions from a unified interface.

Why the Other Options Are Incorrect

B. Send a snapshot to Cisco for technical support: This is primarily a troubleshooting action. It does not directly block or quarantine the detected malware.

C. Forward the result of the investigation to an external threat-analysis engine: External analysis can provide additional intelligence, but forwarding investigation results does not directly remediate the threat. Blocking the malicious file is the more immediate response.

D. Wait for Cisco Threat Response to automatically block the malware: Threat Response does not necessarily block every detected malicious file automatically. Automated remediation depends on the available integrations and configured workflows. Analysts should initiate the appropriate response action rather than assume the file will be blocked automatically.

Reference

Cisco Threat Response User Guide and Cisco AMP for Endpoints documentation — see the sections on responding to malware verdicts and configuring Custom Detections using SHA-256 file hashes.

Which connector is used to integrate Cisco ISE with Cisco FMC for Rapid Threat Containment?


A. pxGrid


B. FTD RTC


C. FMC RTC


D. ISEGrid





A.
  pxGrid

Explanation

Cisco Identity Services Engine (ISE) and Cisco Firepower Management Center (FMC) integrate for Rapid Threat Containment (RTC) using the pxGrid (Platform Exchange Grid) connector. pxGrid is a secure, publish-subscribe framework that enables security technologies to exchange threat intelligence and contextual information in real time.

In this integration, FMC connects to the ISE pxGrid framework as a client to exchange threat and endpoint information. When FMC detects a threat, such as malware identified by AMP or an intrusion detected by IPS, the integration can facilitate containment actions through ISE. ISE can then use network access control capabilities to restrict the affected endpoint, for example, by applying a quarantine VLAN or a downloadable access control list (dACL). This workflow is a core part of the Rapid Threat Containment solution.

Why the Other Options Are Incorrect

B. FTD RTC: Firepower Threat Defense (FTD) is the managed security device that enforces policies. It is not the connector used to integrate FMC and ISE for Rapid Threat Containment. The integration uses pxGrid.

C. FMC RTC: This is not the standard connector name for the integration. FMC participates in the RTC solution, but pxGrid provides the integration framework.

D. ISEGrid: This is not the correct Cisco technology name. The framework is called pxGrid, which stands for Platform Exchange Grid.

Reference

Cisco documentation: "Cisco Rapid Threat Containment" — describes how Cisco Platform Exchange Grid (pxGrid) supports integration between ISE and FMC for threat information exchange and endpoint containment.


Page 6 out of 35 Pages
PreviousNext
1234567891011
300-710 Practice Test Home

What Makes Our Securing Networks with Cisco Firepower (300-710 SNCF) Practice Test So Effective?

Real-World Scenario Mastery: Our 300-710 practice exam don't just test definitions. They present you with the same complex, scenario-based problems you'll encounter on the actual exam.

Strategic Weakness Identification: Each practice session reveals exactly where you stand. Discover which domains need more attention, before Securing Networks with Cisco Firepower (300-710 SNCF) exam day arrives.

Confidence Through Familiarity: There's no substitute for knowing what to expect. When you've worked through our comprehensive 300-710 practice exam questions pool covering all topics, the real exam feels like just another practice session.