Topic 1: Deployment
An engineer runs the command restore remote-manager-backup location 2.2.2.2 admin /Volume/home/admin FTD408566513.zip on a Cisco FMC. After connecting to the repository, the Cisco FTD device is unable to accept the backup file. What is the reason for this failure?
A. The backup file is not in .cfg format.
B. The wrong IP address is used
C. The backup file extension was changed from .tar to .zip.
D. The directory location is incorrect.
Explanation
When performing a backup of a Cisco Firepower Threat Defense (FTD) configuration (often managed via FMC), the resulting archive file is created with a specific format and extension. The native backup file generated by the FTD uses the .tar extension.
If an administrator or system changes this file extension to .zip (or any other format), the restore process on the FTD will fail. The FTD's restore utility expects the exact native archive format, and it cannot recognize or unpack a file with a modified extension, resulting in the "unable to accept the backup file" error.
Why the Other Options Are Incorrect
A. The backup file is not in .cfg format: FTD backups are not stored as flat .cfg text files. They are archived as .tar files. The absence of a .cfg extension is expected and not the cause of the failure.
B. The wrong IP address is used: If the IP address of the remote repository (2.2.2.2) were wrong or unreachable, the command would fail at the initial connection phase. Since the prompt states "After connecting to the repository," the IP is correct and connectivity was established.
D. The directory location is incorrect: Similar to the IP address, if the directory path (/Volume/home/admin) were incorrect, the system would not be able to locate or retrieve the file. Since it attempts to accept the file and fails, the location is assumed to be correct.
Reference
Cisco Documentation: "Cisco Firepower Threat Defense Command Reference" – Section on restore commands, which specifies that the backup file must be the original .tar archive.
A network administrator configured a NAT policy that translates a public IP address to an internal web server IP address. An access policy has also been created that allows any source to reach the public IP address on port 80. The web server is still not reachable from the Internet on port 80. Which configuration change is needed?
A. The intrusion policy must be disabled for port 80.
B. The access policy rule must be configured for the action trust.
C. The NAT policy must be modified to translate the source IP address as well as destination IP address.
D. The access policy must allow traffic to the internal web server IP address.
Explanation:
In Cisco Firepower Threat Defense (FTD), NAT is applied before the Access Control Policy is evaluated. When traffic from the Internet destined for the public IP on port 80 arrives, the FTD first checks the NAT policy. The destination IP is translated to the internal web server's IP address (e.g., from 203.0.113.5 to 192.168.1.100).
After the NAT translation occurs, the Access Control Policy evaluates the packet using the translated (post-NAT) IP address. Since the current Access Control Policy rule only allows traffic to the public IP address on port 80, the packet (now destined for the internal IP) does not match the rule and is dropped by the implicit deny.
To resolve this, the Access Control Policy must be updated to allow traffic to the internal web server IP address on port 80.
Why the Other Options Are Incorrect:
A. The intrusion policy must be disabled for port 80:
Disabling intrusion inspection is not necessary for basic connectivity and would reduce security. The issue is the Access Control Policy dropping the traffic due to the post-NAT IP mismatch.
B. The access policy rule must be configured for the action trust:
Changing the action to Trust would bypass inspection, but the rule still wouldn't match the packet because the destination IP in the rule is the public IP, not the internal IP.
C. The NAT policy must be modified to translate the source IP address as well as destination IP address:
While source NAT (PAT) is often used for outbound traffic, inbound traffic to a published web server typically only requires Destination NAT (DNAT) or port forwarding. Adding source NAT will not fix the Access Control Policy mismatch.
Reference:
Cisco Documentation: "Cisco Firepower Management Center Configuration Guide" – Section on NAT and Access Control Policy Order, which explains that Access Control evaluates traffic after NAT translation (for destination NAT).
The network administrator wants to enhance the network security posture by enabling machine learning tor malware detection due to a concern with suspicious Microsoft executable file types that were seen while creating monthly security reports for the CIO. Which feature must be enabled to accomplish this goal?
A. Spero
B. dynamic analysis
C. static analysis
D. Ethos
Explanation
The Spero engine is a machine learning-based analysis feature in Cisco Advanced Malware Protection (AMP) that specifically targets Microsoft executable file types (such as .exe and .dll files). It performs static analysis on the file's structure and features locally on the FTD (without needing to send it to the cloud or execute it in a sandbox) to determine if the executable is malicious.
Since the administrator is concerned with suspicious Microsoft executable file types and wants to enable machine learning for detection, Spero is the exact feature designed for this purpose.
Why the Other Options Are Incorrect
B. Dynamic analysis: This involves detonating a file in a sandbox (Cisco Threat Grid) to observe its runtime behavior. While powerful, it is not the machine learning-based feature specifically targeting executables locally.
C. Static analysis: While Spero performs static analysis, "static analysis" is a general category, not the specific Cisco feature name that uses machine learning for executables.
D. Ethos: The Ethos engine is used for file grouping and fuzzy fingerprinting to identify malware families and polymorphic variants, not primarily for machine learning-based detection of executable structures.
Reference
Cisco Documentation: "Cisco Firepower Management Center Configuration Guide" – Section on Spero Analysis, which states it uses machine learning to analyze executable files for malicious characteristics.
A network security engineer must export packet captures from the Cisco FMC web browser while troubleshooting an issue. When navigating to the address https://IP>/capture/CAPI/pcap/test.pcap. an error 403: Forbidden is given instead of the PCAP file. Which action must the engineer take to resolve this issue?
A. Disable the HTTPS server and use HTTP instead.
B. Enable the HTTPS server for the device platform policy.
C. Disable the proxy setting on the browser
D. Use the Cisco FTD IP address as the proxy server setting on the browser
Explanation
On a Cisco FMC, generating and downloading a PCAP file directly requires the HTTPS server to be actively enabled on the platform. By default, the FMC's HTTPS server may be disabled or restricted for these specific direct-access capture URLs.
To resolve the 403 Forbidden error, the engineer must enable the HTTPS server in the device platform policy on the managed FTD (or FMC, depending on where the capture is being run). Once the HTTPS server is enabled and the policy is deployed, the FMC/FTD will serve the PCAP file directly over HTTPS to the browser, allowing the download to proceed.
Why the Other Options Are Incorrect
A. Disable the HTTPS server and use HTTP instead: FMC and FTD management interfaces typically require HTTPS for security. Disabling it to use HTTP is not a supported or secure solution for this issue.
C. Disable the proxy setting on the browser: While a browser proxy might interfere with local address access, the 403 Forbidden error is a server-side rejection indicating that the service (HTTPS server for packet captures) is not enabled or permitted.
D. Use the Cisco FTD IP address as the proxy server setting on the browser: This is not a valid configuration. The FTD is not a proxy server for general web traffic.
Reference
Cisco Documentation: "Cisco Firepower Management Center Configuration Guide" – Section on Device Platform Settings and enabling the HTTPS server for packet capture downloads.
A mid-sized company is experiencing higher network bandwidth utilization due to a recent acquisition The network operations team is asked to scale up their one Cisco FTD appliance deployment to higher capacities due to the increased network bandwidth. Which design option should be used to accomplish this goal?
A. Deploy multiple Cisco FTD appliances in firewall clustering mode to increase performance.
B. Deploy multiple Cisco FTD appliances using VPN load-balancing to scale performance
C. Deploy multiple Cisco FTD HA pairs to increase performance
D. Deploy multiple Cisco FTD HA pairs in clustering mode to increase performance
Explanation
When a single Cisco FTD appliance reaches its maximum capacity and the network requires higher bandwidth and throughput, the standard design to scale performance is to deploy multiple FTD appliances in Firepower Threat Defense Clustering.
Clustering allows multiple FTD devices to act as a single logical firewall (a cluster). It distributes the traffic load across all the units in the cluster, providing active-active load balancing and horizontal scaling of throughput and connection capacity. This is specifically designed to handle increased network bandwidth by utilizing the combined processing power of multiple appliances.
Why the Other Options Are Incorrect
B. Deploy multiple Cisco FTD appliances using VPN load-balancing to scale performance: VPN load-balancing is used specifically to distribute remote access VPN sessions across multiple devices. It does not scale general network throughput or firewall inspection performance for regular traffic.
C. Deploy multiple Cisco FTD HA pairs to increase performance: An HA pair (Active/Standby) is designed for redundancy and high availability, not performance scaling. In an Active/Standby HA pair, only one device processes traffic at a time; the standby device does not add to the total throughput.
D. Deploy multiple Cisco FTD HA pairs in clustering mode to increase performance: You cannot deploy "multiple HA pairs in clustering mode." Clustering and HA are distinct deployment modes. While you can combine clustering with redundancy (using Spanned EtherChannels or individual interfaces for cluster control/state replication), the standard phrasing of an "HA pair in clustering mode" is not a valid architecture for scaling. Clustering is the standalone solution for performance scaling.
Reference
Cisco Documentation: "Cisco Firepower Threat Defense Clustering Configuration Guide" – Section on Clustering for Scalability, which explains how clustering increases throughput and performance
An engineer is troubleshooting connectivity to the DNS servers from hosts behind a new Cisco FTD device. The hosts cannot send DNS queries to servers in the DMZ. Which action should the engineer take to troubleshoot this issue using the real DNS packets?
A. Use the Connection Events dashboard to check the block reason and adjust the inspection policy as needed.
B. Use the packet capture tool to check where the traffic is being blocked and adjust the access control or intrusion policy as needed.
C. Use the packet tracer tool to determine at which hop the packet is being dropped
D. Use the show blocks command in the Threat Defense CLI tool and create a policy to allow the blocked traffic.
Explanation
When hosts cannot send DNS queries through a Cisco FTD, and the engineer specifically wants to troubleshoot using the real DNS packets, the most effective tool is the packet capture tool.
The packet capture feature on FTD allows the engineer to capture the actual traffic at the interface level and view the trace (or packet trace) to see exactly how the FTD processed the packet. This trace shows whether the packet was dropped by the Access Control Policy (e.g., a block rule or implicit deny), the Security Intelligence feed, or the Snort/Intrusion engine. Once the drop point is identified from the real packets, the engineer can adjust the corresponding policy (Access Control or Intrusion) to allow the DNS traffic.
Why the Other Options Are Incorrect
A. Use the Connection Events dashboard to check the block reason and adjust the inspection policy as needed:
Connection events are useful for viewing logs, but they do not show the real packets. The question specifically asks to troubleshoot using the real DNS packets, which requires a packet capture.
C. Use the packet tracer tool to determine at which hop the packet is being dropped:
The packet tracer tool in FMC is a simulation tool. It uses synthetic packets based on configured parameters, not the actual live DNS packets.
D. Use the show blocks command in the Threat Defense CLI tool and create a policy to allow the blocked traffic:
The show blocks command shows recent block events (specifically for Security Intelligence or certain access control drops) but does not capture the real packets for deep analysis. It is also less comprehensive than a full packet capture with trace.
Reference
Cisco Documentation: "Cisco Firepower Management Center Configuration Guide" – Section on Packet Captures, which explains how to capture real traffic and use the trace feature to identify where packets are being blocked.
An engineer is investigating connectivity problems on Cisco Firepower for a specific SGT. Which command allows the engineer to capture real packets that pass through the firewall using an SGT of 64?
A. capture CAP type inline-tag 64 match ip any any
B. capture CAP match 64 type inline-tag ip any any
C. capture CAP headers-only type inline-tag 64 match ip any any
D. capture CAP buffer 64 match ip any any
Explanation
On a Cisco Firepower Threat Defense (FTD) device, the built-in packet capture utility (`capture` command) can filter traffic based on a Security Group Tag (SGT). The correct CLI syntax to capture traffic based on an inline SGT is to use the `type inline-tag` keyword followed by the specific tag value.
The command format is:
`capture
Therefore, to capture packets with an SGT of 64, the correct command is:
`capture CAP type inline-tag 64 match ip any any`
Why the Other Options Are Incorrect
B. capture CAP match 64 type inline-tag ip any any:
The syntax is incorrect. The `type inline-tag` must come before the `match` keyword, and the tag value (`64`) should follow `type inline-tag`, not precede it.
C. capture CAP headers-only type inline-tag 64 match ip any any:
While the SGT filtering syntax is correct, the question asks for the command that allows capturing real packets. The `headers-only` keyword captures only packet headers and discards the payload, which defeats the purpose of capturing the full real packet.
D. capture CAP buffer 64 match ip any any:
This syntax uses `buffer 64`, which sets the capture buffer size to 64 bytes, not an SGT filter. This would result in an invalid or useless capture.
Reference
Cisco Documentation: "Cisco Firepower Threat Defense Command Reference" – Section on the `capture` command, specifically the `type inline-tag` keyword for filtering based on Security Group Tags.
A network administrator registered a new FTD to an existing FMC. The administrator cannot place the FTD in transparent mode. Which action enables transparent mode?
A. Add a Bridge Group Interface to the FTD before transparent mode is configured
B. Dereglster the FTD device from FMC and configure transparent mode via the CLI.
C. Obtain an FTD model that supports transparent mode
D. Assign an IP address to two physical interfaces.
Explanation
In Cisco Firepower Threat Defense (FTD), the firewall mode (Routed vs. Transparent) is a fundamental system setting that dictates how the device handles interfaces and traffic. Once an FTD device is registered to the FMC and configured in Routed mode (the default), you cannot simply switch it to Transparent mode from the FMC GUI.
To change the firewall mode to Transparent, the device must be reset. The standard procedure is:
1. Deregister (delete) the FTD from the FMC.
2. Access the FTD via the CLI (console or SSH).
3. Run the command `configure firewall transparent`.
4. Save the configuration and reload the device.
5. Re-register the FTD back to the FMC.
Why the Other Options Are Incorrect
A. Add a Bridge Group Interface to the FTD before transparent mode is configured:
Bridge Groups are used within transparent mode (or routed mode for IRB). Adding a BVI does not switch the device's operating mode from routed to transparent.
C. Obtain an FTD model that supports transparent mode:
All standard Cisco FTD hardware and virtual platforms support transparent mode. The issue is the configuration state, not the hardware model.
D. Assign an IP address to two physical interfaces:
Assigning IP addresses is a characteristic of Routed mode. In Transparent mode, the physical interfaces do not have IP addresses (except for management, or the BVI).
Reference
Cisco Documentation: "Cisco Firepower Management Center Configuration Guide" – Section on Changing the Firewall Mode, which states that an FTD must be deregistered and configured via CLI to switch to transparent mode.
A security engineer found a suspicious file from an employee email address and is trying to upload it for analysis, however the upload is failing. The last registration status is still active. What is the cause for this issue?
A. Cisco AMP for Networks is unable to contact Cisco Threat Grid on premise
B. Cisco AMP for Networks is unable to contact Cisco Threat Grid Cloud
C. There is a host limit set
D. The user agent status is set to monitor
Explanation
C. There is a host limit set.
When uploading a file for analysis in Cisco AMP for Endpoints, if the upload fails despite the endpoint's registration status being active, the most common cause is a host limit restriction.
Cisco AMP for Endpoints enforces host limits based on the licensing agreement. The host limit dictates the maximum number of endpoints that can be registered and actively upload files for analysis. Once this limit is reached, endpoints may still show as "registered" or "active," but they will be prevented from submitting new files for analysis to the cloud (or on-premise Threat Grid). The administrator must check the AMP portal to see if the number of active hosts has exceeded the licensed limit, or if a specific host limit policy is preventing the upload.
Why the Other Options Are Incorrect
A. Cisco AMP for Networks is unable to contact Cisco Threat Grid on premise:
The scenario describes a file from an employee email address being uploaded, which is an endpoint action. AMP for Networks is a different product (network-level inspection). If the endpoint is integrated with AMP for Endpoints, the connection is to the AMP Cloud (or the specific Threat Grid integrated with it), not an on-premise Threat Grid appliance via AMP for Networks.
B. Cisco AMP for Networks is unable to contact Cisco Threat Grid Cloud:
Again, the context is an employee's email and endpoint registration status, not network traffic inspection via AMP for Networks.
D. The user agent status is set to monitor:
The "user agent status" or "monitor mode" affects how the endpoint connector reacts to detected threats (e.g., monitoring vs. blocking). It does not prevent a file from being uploaded for cloud analysis; in fact, monitoring mode still requires the file hash to be checked in the cloud.
Reference
Cisco Documentation: "Cisco AMP for Endpoints User Guide" – Section on Host Limits and Licensing, which explains that exceeding the licensed host limit can prevent endpoints from uploading files or receiving updated cloud intelligence.
A network administrator is deploying a Cisco IPS appliance and needs it to operate initially without affecting traffic flows. It must also collect data to provide a baseline of unwanted traffic before being reconfigured to drop it. Which Cisco IPS mode meets these requirements?
A. failsafe
B. inline tap
C. promiscuous
D. bypass
Explanation
When deploying a Cisco IPS appliance, the administrator wants to collect data to establish a baseline of unwanted traffic without affecting traffic flows. This means the IPS must only monitor a copy of the traffic and generate alerts, but it cannot drop or disrupt the traffic.
Promiscuous mode (also known as Passive or IDS mode) meets these exact requirements. In promiscuous mode, the IPS interface receives a copy of the network traffic (via a SPAN port or network tap) but is not inline with the production traffic path. It analyzes the traffic for malicious activity and logs events, but it does not have the capability to drop packets, ensuring that normal traffic flows are completely unaffected. Once the baseline is established and rules are tuned, the administrator can then reconfigure the device for inline mode to drop threats.
Why the Other Options Are Incorrect
A. failsafe:
Failsafe is a feature (failsafe mode) used in inline deployments. If the IPS fails or loses power, failsafe ensures that traffic continues to flow by bridging the interfaces. It is not a deployment mode for baseline data collection.
B. inline tap:
Inline tap (or Tap mode) is a feature used with inline sets to monitor traffic passively. While it does not disrupt traffic, it still requires the interfaces to be physically inline (connected between two devices). The question implies the device is operating initially without being in the traffic path, which is the classic definition of promiscuous (passive) mode for an IPS appliance.
D. bypass:
Bypass mode is similar to failsafe, where traffic is allowed to pass through the device without inspection in the event of a failure or overload. It does not provide data collection for baselining.
Reference
Cisco Documentation: "Cisco Intrusion Prevention System Deployment Guide" – Section on Promiscuous (Passive/IDS) Mode, which explains how this mode monitors traffic without affecting the flow and is used for baselining.
A network administrator is configuring Snort inspection policies and is seeing failed deployment messages in Cisco FMC. What information should the administrator generate for Cisco TAC to help troubleshoot?
A. A "show tech" file for the device in question
B. A "troubleshoot" file for the device in question.
C. A "troubleshoot" file for the Cisco FMC.
D. A "show tech" for the Cisco FMC.
Explanation
When a policy deployment fails on a Cisco Firepower Threat Defense (FTD) device managed by the FMC—especially an issue related to Snort inspection policies—the most critical piece of information for Cisco TAC is the troubleshoot file generated for that specific managed device.
This file contains detailed logs of the policy deployment process, Snort policy compilation errors, rule validation failures, and the device's system state. It captures exactly what happened during the failed deployment, allowing TAC to pinpoint the exact rule or configuration issue causing the failure.
Why the Other Options Are Incorrect
A. A "show tech" file for the device in question:
A `show tech` file provides general system health and configuration data. It does not contain the specific Snort compilation logs and policy deployment traces needed to troubleshoot a failed policy deployment.
C. A "troubleshoot" file for the Cisco FMC:
This file captures the management platform's state. Since the failure is happening on the managed device (Snort inspection policies failing to deploy), the device's troubleshoot file is required.
D. A "show tech" for the Cisco FMC:
Similar to option C, this focuses on the FMC server and does not contain the detailed device-side deployment error logs.
Reference
Cisco Documentation: "Cisco Firepower Management Center Configuration Guide" – Section on Troubleshooting Policy Deployments, which explains how to generate troubleshoot files for managed devices to diagnose deployment failures.
Which Cisco FMC report gives the analyst information about the ports and protocols that are related to the configured sensitive network for analysis?
A. Malware Report
B. Host Report
C. Firepower Report
D. Network Report
Explanation
In Cisco Firepower Management Center (FMC), the Host Report is designed to provide detailed information about a specific host on the network. This report includes sections that list the protocols and ports observed for that host, which directly helps an analyst understand the network activity associated with a sensitive host.
According to Cisco documentation, the Host Report template provides information about a specific host on the network, and it includes sections that detail the protocols detected in the traffic associated with that host. This is the most appropriate report for analyzing ports and protocols related to a configured sensitive network host.
Why the Other Options Are Incorrect
A. Malware Report:
This report focuses on malware events and file dispositions, not on the ports and protocols associated with a specific sensitive host.
C. Firepower Report:
This is a general report template that provides overall information about the organization's network, but it does not specifically focus on the ports and protocols of a single sensitive host.
D. Network Report:
While a Network Risk Report exists, it is a high-level summary of risks on the network and does not provide the detailed port and protocol breakdown for a specific sensitive host that the Host Report offers.
Reference
Cisco Documentation: "FireSIGHT System User Guide" – Section on Predefined Report Templates, which states the Host Report provides information about a specific host on the network, including protocols detected in the traffic associated with that host.
| Page 15 out of 35 Pages |
| 1011121314151617181920 |
| 300-710 Practice Test Home |
Real-World Scenario Mastery: Our 300-710 practice exam don't just test definitions. They present you with the same complex, scenario-based problems you'll encounter on the actual exam.
Strategic Weakness Identification: Each practice session reveals exactly where you stand. Discover which domains need more attention, before Securing Networks with Cisco Firepower (300-710 SNCF) exam day arrives.
Confidence Through Familiarity: There's no substitute for knowing what to expect. When you've worked through our comprehensive 300-710 practice exam questions pool covering all topics, the real exam feels like just another practice session.