Free 300-710 Practice Test Questions 2026

420 Questions


Last Updated On : 19-Nov-2026


Topic 1: Deployment

A network administrator notices that SI events are not being updated The Cisco FTD device is unable to load all of the SI event entries and traffic is not being blocked as expected. What must be done to correct this issue?


A. Restart the affected devices in order to reset the configurations


B. Manually update the SI event entries to that the appropriate traffic is blocked


C. Replace the affected devices with devices that provide more memory


D. Redeploy configurations to affected devices so that additional memory is allocated to the SI module





D.
  Redeploy configurations to affected devices so that additional memory is allocated to the SI module

Explanation

The correct answer is D. Redeploy configurations to affected devices so that additional memory is allocated to the SI module.

Cisco Firepower Threat Defense (FTD) mein Security Intelligence (SI) events ko process aur load karne ke liye ek specific amount of memory allocate hoti hai. Jab SI feeds ya entries bahut zyada ho jati hain, to FTD device un sab ko memory mein load nahi kar pata. Is wajah se events update hona band ho jate hain aur traffic block hone ki bajaye pass hone lagta hai.

Is issue ko resolve karne ke liye FMC (Firepower Management Center) se configuration ko redeploy karna hota hai. Redeploy karne par FTD device apne SI module ke liye additional memory allocate karta hai (ya memory allocation ko re-adjust karta hai) taake saari SI entries properly load ho sakein aur traffic blocking resume ho jaye.

Why the Other Options Are Incorrect

A. Restart the affected devices in order to reset the configurations: Device restart karne se sirf temporary fix hota hai. Agar memory allocation insufficient hai, to restart ke baad phir wahi issue aa jayega jab SI entries load hongi.

B. Manually update the SI event entries so that the appropriate traffic is blocked: SI entries manually update karna scalable nahi hai aur root cause (memory allocation issue) ko solve nahi karta.

C. Replace the affected devices with devices that provide more memory: Har situation mein hardware replace karna zaroori nahi hota. FTD software mein redeploy karne se memory properly allocate ho jati hai bina hardware change kiye.

Reference

Cisco Documentation: "Cisco Firepower Management Center Configuration Guide" – Section on Security Intelligence (SI) and Troubleshooting SI memory allocation issues.

A user within an organization opened a malicious file on a workstation which in turn caused a ransomware attack on the network. What should be configured within the Cisco FMC to ensure the file is tested for viruses on a sandbox system?


A. Capacity handling


B. Local malware analysis


C. Spere analysis


D. Dynamic analysis





D.
  Dynamic analysis

Explanation

To test a file for viruses/malware using a sandbox system (such as Cisco Threat Grid), you must configure Dynamic Analysis within the Cisco FMC file policy. Dynamic analysis takes files that are unknown or suspicious and detonates them in a secure, isolated virtual environment (the sandbox) to observe their behavior (e.g., registry changes, network callbacks, file encryption attempts). If the file exhibits malicious behavior during this execution, the sandbox marks it as malware, and the FMC can then take action (like blocking or quarantining) on subsequent downloads. This is specifically designed to catch advanced threats like ransomware that may not be detected by signature-based engines.

Why the Other Options Are Incorrect

A. Capacity handling: This is a file policy setting used to determine what action the system should take when the maximum number of file inspections is reached, not for sandboxing.

B. Local malware analysis: This performs a static analysis of the file's structure locally on the FTD device to detect malicious patterns. It does not execute the file in a sandbox environment.

C. Spero analysis: Spero is a machine-learning based engine that analyzes the file's structure and features (static analysis) to identify unknown malware. It does not run the file in a sandbox.

Reference

Cisco Documentation: "Cisco Firepower Management Center Configuration Guide" – Section on File Policies and Malware Protection, specifically Dynamic Analysis (sandboxing via Cisco Threat Grid).

An engineer wants to change an existing transparent Cisco FTD to routed mode. The device controls traffic between two network segments. Which action is mandatory to allow hosts to reestablish communication between these two segments after the change?


A. remove the existing dynamic routing protocol settings.


B. configure multiple BVIs to route between segments.


C. configure multiple BVIs to route between segments.


D. implement non-overlapping IP subnets on each segment





D.
  implement non-overlapping IP subnets on each segment

Explanation

D. implement non-overlapping IP subnets on each segment.

When a Cisco FTD operates in transparent mode (Layer 2), it can bridge traffic between two network segments even if they are on the same IP subnet. The hosts use the firewall interfaces simply as Layer 2 switches, and the FTD does not act as a gateway.

However, when you change the deployment mode to routed mode (Layer 3), the FTD becomes a router. A router requires each of its interfaces (or BVIs) to be in a different, non-overlapping IP subnet to route traffic between them. If the two segments are still on the same subnet after the change, the FTD will not route the traffic, and the hosts will lose connectivity. Therefore, to allow hosts to reestablish communication through the routed FTD, you must readdress the segments so they reside on unique, non-overlapping subnets, and configure the FTD interfaces as the default gateways for those hosts.

Why the Other Options Are Incorrect

A. remove the existing dynamic routing protocol settings: Dynamic routing protocols are not the cause of the connectivity loss during a mode change. They are optional and can be used in routed mode.

B. configure multiple BVIs to route between segments: While BVIs can be used in routed mode for bridging, they are not mandatory just to route between two segments. Regular routed interfaces can do this. The core issue is the IP subnet overlap.

C. assign unique VLAN IDs to each firewall interface: VLAN IDs are used for tagging traffic, but assigning unique VLANs does not solve the Layer 3 routing problem if the IP subnets overlap.

Reference

Cisco Documentation: "Cisco Firepower Management Center Configuration Guide" – Section on Transparent vs. Routed Mode, which explains that transparent mode allows bridging of same-subnet traffic, while routed mode requires different subnets.

Which protocol is needed to exchange threat details in rapid threat containment on Cisco FMC?


A. SGT


B. SNMP v3


C. BFD


D. pxGrid





D.
  pxGrid

Explanation

Rapid Threat Containment (RTC) is a Cisco security architecture that integrates different security products to automate threat response. In the integration between Cisco Firepower Management Center (FMC) and Cisco Identity Services Engine (ISE), the protocol used to exchange threat details and context is pxGrid (Platform Exchange Grid).

When FMC detects a threat (e.g., via AMP or IPS), it publishes the threat event and the associated host IP to ISE over pxGrid. ISE then uses this information to take remediation actions, such as quarantining the endpoint or applying a restrictive Security Group Tag (SGT).

Why the Other Options Are Incorrect

A. SGT (Security Group Tag): SGT is a tag used for identity-based segmentation (TrustSec), not the protocol used to exchange threat intelligence between FMC and ISE.

B. SNMP v3: SNMP is used for monitoring and management, not for exchanging threat details for containment.

C. BFD (Bidirectional Forwarding Detection): BFD is a network protocol used for fast failure detection in routing protocols, not for threat containment.

Reference

Cisco Documentation: "Cisco Rapid Threat Containment" – Explains the use of pxGrid for integrating FMC and ISE.

An engineer is setting up a new Firepower deployment and is looking at the default FMC
policies to start the implementation During the initial trial phase, the organization wants to
test some common Snort rules while still allowing the majority of network traffic to pass
Which default policy should be used?


A.

Maximum Detection


B.

Security Over Connectivity


C.

Balanced Security and Connectivity


D.

Connectivity Over Security





D.
  

Connectivity Over Security



Explanation

During an initial trial phase, the organization wants to test some common Snort rules while still allowing the majority of network traffic to pass. This means the priority is network availability and minimizing false positives, rather than aggressive threat blocking.

Cisco FMC provides several default Intrusion Policies. The Connectivity Over Security policy is the most permissive. It focuses on maintaining network connectivity and only enables a very small set of highly reliable Snort rules, mostly for known, severe threats. It allows the vast majority of traffic to pass without deep inspection, which is ideal for a trial phase where you want to observe traffic and test basic rules without disrupting the network.

Why the Other Options Are Incorrect

A. Maximum Detection: This is the most aggressive policy. It enables a massive number of Snort rules and is designed to catch as many threats as possible, which can result in high false positives and blocked legitimate traffic. It is not suitable for a trial phase where the goal is to allow most traffic.

B. Security Over Connectivity: This policy prioritizes security and blocks more traffic. It enables a larger ruleset than Balanced or Connectivity modes, increasing the risk of disrupting legitimate traffic.

C. Balanced Security and Connectivity: This is the default, middle-ground policy. It provides a good balance, but if the goal is specifically to allow the majority of traffic while only testing some rules, the Connectivity Over Security policy is the safest choice for a trial phase to avoid unexpected disruptions.

Reference

Cisco Documentation: Cisco Firepower Management Center Configuration Guide – Section on Intrusion Policy Base Policies (Connectivity Over Security, Balanced Security and Connectivity, Security Over Connectivity, and Maximum Detection).

After using Firepower for some time and learning about how it interacts with the network, an administrator is trying to correlate malicious activity with a user Which widget should be configured to provide this visibility on the Cisco Firepower dashboards?


A. Custom Analysis


B. Current Status


C. Current Sessions


D. Correlation Events





D.
  Correlation Events

Explanation

The Correlation Events widget on the Cisco Firepower Management Center (FMC) dashboard is designed to show statistics about correlation events generated by the system. These events are created when the system correlates different types of data, such as intrusion events, discovery data, and user identity, to identify malicious activity and associate it with specific users.

By configuring this widget, the administrator can see a summary of high-priority threats and attacks, which helps in correlating malicious activity with the users involved in that traffic.

Why the Other Options Are Incorrect

A. Custom Analysis: This is a separate tool used to build custom charts and graphs based on specific filters, not a standard dashboard widget for real-time correlation of threats to users.

B. Current Status: This widget shows the overall health and status of the FMC and managed devices, not malicious activity or user correlation.

C. Current Sessions: This widget displays the users who are currently logged into the FMC appliance itself, not the network users or threats associated with them.

Reference

Cisco Documentation: Cisco Firepower Management Center Configuration Guide – Section on Dashboard Widgets, specifically the Correlation Events widget.

An administrator is working on a migration from Cisco ASA to the Cisco FTD appliance and needs to test the rules without disrupting the traffic. Which policy type should be used to configure the ASA rules during this phase of the migration?


A. identity


B. Intrusion


C. Access Control


D. Prefilter





D.
  Prefilter

Explanation

When migrating from a Cisco ASA to a Cisco FTD appliance, a key challenge is translating and testing ASA access control lists (ACLs) without causing a network outage. The Prefilter Policy in the Cisco FMC is the ideal tool for this phase because it evaluates traffic before the main Access Control Policy and before deep inspection (Snort) occurs.

By using Prefilter rules, the administrator can quickly implement Fastpath rules that either Trust (allow) or Block traffic based on simple Layer 3/4 criteria (matching the ASA ACLs). Because Prefilter rules can bypass Snort deep inspection, they can reduce processing overhead and can be tested carefully. If a rule is incorrect, it can be adjusted without the processing overhead of the full Access Control Policy inspection path.

Why the Other Options Are Incorrect

A. Identity Policy: This policy is used to determine user identity through passive or active authentication. It does not handle ASA-style Layer 3/4 ACL rules or traffic bypassing.

B. Intrusion Policy: Intrusion policies contain Snort rules for deep packet inspection. They are not used to replicate basic ASA allow/deny ACLs.

C. Access Control Policy: While you can put rules in the Access Control Policy, it is more complex and processes traffic through the main rule engine and inspection paths. The Prefilter Policy is specifically designed for early traffic handling, including Fastpath rules based on Layer 3/4 criteria, making it a suitable place to stage legacy ASA rules during a migration.

Reference

Cisco Documentation: Cisco Firepower Management Center Configuration Guide – Section on Prefilter Policies and Fastpath rules, which explains their use for early traffic handling.

Cisco Documentation: Migrating from ASA to FTD – Guidance on migrating legacy access control configurations.

What is the advantage of having Cisco Firepower devices send events to Cisco Threat Response via the security services exchange portal directly as opposed to using syslog?


A. All types of Cisco Firepower devices are supported


B. An on-premises proxy server does not need to be set up and maintained.


C. Cisco Firepower devices do not need to be connected to the Internet.


D. Supports all devices that are running supported versions of Cisco Firepower.





B.
  An on-premises proxy server does not need to be set up and maintained.

Explanation

Cisco Threat Response (now Cisco SecureX) can ingest events from Cisco Firepower devices in two primary ways: via the Security Services Exchange (SSE) portal directly, or via an on-premises Cisco Threat Response proxy.

When a Firepower device is configured to send events directly to SSE, the FMC establishes a secure cloud connection to Cisco's cloud infrastructure. The major advantage of this direct cloud connection is that it eliminates the need to deploy, manage, and maintain an on-premises proxy server. The on-premises proxy is only required if the security policy dictates that no devices can connect directly to the internet, or if there are strict firewall rules preventing outbound cloud connections. By using SSE directly, the architecture is simpler, and the administrative overhead of maintaining proxy hardware/software is removed.

Why the Other Options Are Incorrect

A. All types of Cisco Firepower devices are supported: This is not the advantage of the direct SSE connection. In fact, certain older hardware or specific virtual deployments might have restrictions, and both methods support the same core Firepower device types.

C. Cisco Firepower devices do not need to be connected to the Internet: This is completely false. To send events directly to the SSE portal, the Firepower devices or the FMC must have an internet connection to reach the Cisco cloud.

D. Supports all devices that are running supported versions of Cisco Firepower: While true, this is a baseline requirement for both syslog/proxy and direct SSE methods, not the specific advantage of bypassing the proxy.

Reference

Cisco Documentation: Cisco Threat Response User Guide – Section on integrating Firepower devices via the Security Services Exchange (SSE) versus the on-premises proxy, which highlights the removal of the proxy requirement as a primary benefit of direct cloud integration.

While configuring FTD, a network engineer wants to ensure that traffic passing through the
appliance does not require routing or Vlan rewriting. Which interface mode should the
engineer implement to accomplish this task?


A.

passive


B.

transparent


C.

Inline tap


D.

Inline set





B.
  

transparent



An analyst using the security analyst account permissions is trying to view the Correlations Events Widget but is not able to access it. However, other dashboards are accessible. Why is this occurring?


A. An API restriction within the Cisco FMC is preventing the widget from displaying


B. The widget is configured to display only when active events are present


C. The widget is not configured within the Cisco FMC.


D. The security analyst role does not have permission to view this widget





D.
  The security analyst role does not have permission to view this widget

Explanation

In Cisco Firepower Management Center (FMC), dashboard widget visibility is controlled by the user's assigned role and permissions. According to Cisco documentation, the Correlation Events widget requires the appropriate menu-based permissions to view it.

If an analyst with only the Security Analyst account permissions cannot see the widget while other dashboards are accessible, it may indicate a permission restriction. The FMC allows administrators to customize roles, and it is possible that the specific Security Analyst role in this deployment has been modified or is missing the sub-permission required to view Correlation Events. Cisco also notes that not all user roles have access to all dashboard widgets. If a dashboard created by a higher-privileged user is viewed by a lower-privileged user, some widgets may be disabled or unavailable.

Why the Other Options Are Incorrect

A. An API restriction within the Cisco FMC is preventing the widget from displaying: API restrictions are related to programmatic access and integrations, not the internal role-based visibility of dashboard widgets in the web interface.

B. The widget is configured to display only when active events are present: The Correlation Events widget displays a graph of event rates over time, even if the rate is zero. It does not completely hide itself from the dashboard based on the absence of active events.

C. The widget is not configured within the Cisco FMC: The question states that the analyst is trying to view it, implying it exists on the dashboard being accessed. If it were not configured at all, it would not appear on the dashboard for anyone.

Reference

Cisco Documentation: Firepower Management Center Configuration Guide – Section on User Roles and Dashboard Widget Permissions, covering user permissions and access to dashboard widgets.

The administrator notices that there is malware present with an .exe extension and needs to verify if any of the systems on the network are running the executable file. What must be configured within Cisco AMP for Endpoints to show this data?


A. prevalence


B. threat root cause


C. vulnerable software


D. file analysis





A.
  prevalence

Explanation

In Cisco AMP for Endpoints, the Prevalence feature is used to determine how widely a specific file, identified by its SHA-256 hash, is observed across the global AMP user base. By looking up the prevalence data for a specific .exe file, the administrator can see whether the file is common, rare, or unique. They can also view the prevalence within their own organization's endpoints. This allows the administrator to verify whether any internal systems have the specific executable, helping assess the risk and scope of a potential malware presence.

Why the Other Options Are Incorrect

B. Threat root cause: This feature helps determine how a threat entered the network, such as through a specific email or web download. While useful, it does not directly answer the question of which systems are running the file.

C. Vulnerable software: This refers to software with known vulnerabilities (CVEs) that could be exploited. It is a separate feature and does not track the prevalence of specific malicious file hashes.

D. File analysis: This involves submitting the file to the AMP cloud or Threat Grid for dynamic or static analysis to determine its behavior. It does not primarily show the file's prevalence across the organization's endpoints.

Reference

Cisco Documentation: Cisco AMP for Endpoints User Guide – Section on File Prevalence, which explains how to view a file's prevalence across global and local environments to help determine its scope.

What is a characteristic of bridge groups on a Cisco FTD?


A. In routed firewall mode, routing between bridge groups must pass through a routed interface.


B. In routed firewall mode, routing between bridge groups is supported


C. In transparent firewall mode, routing between bridge groups is supported


D. Routing between bridge groups is achieved only with a router-on-a-stick configuration on a connected router





B.
  In routed firewall mode, routing between bridge groups is supported

Explanation

On a Cisco Firepower Threat Defense (FTD) device, a bridge group allows multiple interfaces to act as a Layer 2 switch. When the FTD is in routed firewall mode, you can configure a Bridge Virtual Interface (BVI) for each bridge group.

The BVI allows the bridge group to participate in Layer 3 routing. Because the BVI has an IP address, the FTD can route traffic between different bridge groups, as well as between a bridge group and a standard routed interface. This feature is known as Integrated Routing and Bridging (IRB).

Therefore, in routed mode, the FTD itself performs the routing between bridge groups.

Why the Other Options Are Incorrect

A. In routed firewall mode, routing between bridge groups must pass through a routed interface: This is false. The FTD can route directly between the BVIs of different bridge groups without requiring traffic to pass through a separate physical routed interface.

C. In transparent firewall mode, routing between bridge groups is supported: In transparent mode, the FTD primarily operates as a Layer 2 firewall and does not perform normal Layer 3 routing between bridge groups. Therefore, it cannot route traffic between bridge groups in the same way as routed mode.

D. Routing between bridge groups is achieved only with a router-on-a-stick configuration on a connected router: This is false. The FTD itself can perform routing between bridge groups when configured in routed mode with the appropriate BVI interfaces. An external router-on-a-stick is not required.

Reference

Cisco Documentation: Cisco Firepower Management Center Configuration Guide – Section on Bridge Virtual Interfaces (BVI) and Integrated Routing and Bridging (IRB) in Routed Mode.


Page 12 out of 35 Pages
PreviousNext
7891011121314151617
300-710 Practice Test Home

What Makes Our Securing Networks with Cisco Firepower (300-710 SNCF) Practice Test So Effective?

Real-World Scenario Mastery: Our 300-710 practice exam don't just test definitions. They present you with the same complex, scenario-based problems you'll encounter on the actual exam.

Strategic Weakness Identification: Each practice session reveals exactly where you stand. Discover which domains need more attention, before Securing Networks with Cisco Firepower (300-710 SNCF) exam day arrives.

Confidence Through Familiarity: There's no substitute for knowing what to expect. When you've worked through our comprehensive 300-710 practice exam questions pool covering all topics, the real exam feels like just another practice session.