What Is a key differentiator of generate routes from aggregate routes?

A. Generate routes use a forwarding next hop.

B. Generate routes have a default next-hop value of reject.

C. Generate routes have a default preference value of 210.

D. Generate routes cannot be used as a gateway of last resort.

You are asked to configure filter-based forwarding on a Junos device. Which two statements are correct in this scenario? (Choose two.)

A. You must create a routing policy.

B. You must create a route target.

C. You must create and apply a match filter.

D. You must create a routing instance.

How does a Junos device learn about MAC addresses when II is first connected to an Ethernet LAN?

A. The device sends out a network broadcast message asking tor all devices and MAC addresses on the network and stores this information In addition lo the interface from which the response was received.

B. The device learns the destination MAC addresses from traffic in the network and stores this MAC address in addition to the interface from which the traffic was received.

C. The device learns the source MAC addresses from traffic in the network and stores this MAC address in addition to the interface from which the traffic was received.

D. The device sends out a network multicast message asking for all devices and MAC addresses on the network and stores this Information in addition to the interface from which the response was received.

An OSPF router does not have a router ID configured. In this scenario, which statement is correct about the router ID?

A. The Junos OS will use the IP address assigned to the interface with the lowest MAC address.

B. A router ID will not be assigned until it is manually configured.

C. The Junos OS will use the IP address assigned to the loopback interface for the router.

D. The Junos OS will use the IP address assigned to the Interface with the highest priority.

Which two statements ate correct about the BGP next-hop attribute value? (Choose two.)

A. By default, the next-hop value is changed across IBGP links.

B. By default, the next-hop value is changed across EBGP links.

C. By default, the next-hop value is not changed across IBGP links.

D. By default, the next-hop value is not changed across EBGP links.

Interface ge-0/0/0.0 connects you network to your ISP. You want to advertise this interface address as an Internal route In OSPF without creating a neighbor with your ISP. In this scenario, how is this task accomplished?

A. Remove interface ge-0/0/0.0 from OSPF.

B. Create a generated route for Interface ge-0/0/0.0.

C. Add ge-0/0/0.0 as a passive interface In OSPF.

D. Configure a static route for Interface ge-0/0/0.0.

Which statement describes integrated routing and bridging (IRB) interfaces?

A. An IRB interface Is an IP gateway For hosts of a bridge domain.

B. An IRB interface assigns interfaces to VLANs.

C. An IRB interface enables Layer 2 switching on the router.

D. An IRB interface defines a bridge domain.

Which two steps are required to enable MPLS on a physical interface in Junos? (Choose two.)

A. Add family mpls on the interface.

B. Add the loopback interface under protocols mpls.

C. Add family mpls on the loopback interface.

D. Add the interface under protocols mpls.

You are deploying link aggregation groups. By default, what are two considerations in this scenario? (Choose two.)

A. There should only be four member links per LAG.

B. All the ports must have the same speed.

C. Member links are required to be contiguous ports.

D. Member links can reside on different members within an MC-LAG.

You are troubleshooting two OSPF routers that have an adjacency that remains in the ExStart state. What would cause this problem?

A. mismatched OSPF hello intervals on the OSPF interfaces

B. mismatched authentication settings on the OSPF interfaces

C. mismatched MTU settings on the OSPF interfaces

D. mismatched subnet settings on the OSPF interfaces

Which LSA type does an OSPF ABR use to advertise external routes generated by an NSSAASBR into the backbone?

A. Type 5

B. Type 7

C. Type 3

D. Type 1

You are asked to create connections between routing instances on the same Junos device and route between the connected Instances. What are two ways to accomplish this task? (Choose two.)

A. Use physical interfaces.

B. Use an IRB interface.

C. Use logical tunnel interfaces.

D. Use loopback interfaces.