Free 350-101 Practice Test Questions 2026

An engineer is migrating to a new Cisco Catalyst CW9800-H1 WLC to modernize the wireless infrastructure and enable advanced monitoring capabilities. The organization operates more than 150 access points and uses Cisco Catalyst Center for centralized network management and assurance. As part of the deployment, the engineer must enable wireless service assurance and wireless telemetry to monitor client connectivity, roaming behavior, and performance metrics across the wireless network. Which configuration must be applied in Cisco Catalyst Center when onboarding the WLC?

A. Configure CLI and SNMP credentials and the NETCONF port during device discovery and ensure that device controllability is enabled under device settings. When discovered, assign the WLC and APs to a site with wireless telemetry enabled.

B. Configure CLI and SNMP credentials and the NETCONF port during device discovery and ensure that wireless telemetry is enabled under system settings. When discovered, assign the WLC to a site with device controllability enabled.

C. Enable CLI, SNMP, and NETCONF credentials during device discovery and ensure that wireless assurance is enabled globally. When discovered, assign the WLC to a site with device controllability enabled.

D. Enable CLI, SNMP, and NETCONF credentials during device discovery and ensure that device controllability is enabled globally. When discovered, assign the WLC to a site with wireless assurance enabled.

A network engineer is deploying a new wireless monitoring solution in a large campus. The engineer must connect Cisco Spaces Connector, Cisco ISE, and a Catalyst Center appliance to the switch infrastructure. All three services require management and telemetry connectivity, and the security policy mandates segregation of management and user traffic. The engineer also must ensure that any network changes do not disrupt ongoing wireless services for users and staff. Which implementation must the engineer use on the switch interfaces?

A. Configure PortFast on each separate interface to speed up convergence.

B. Assign the management VLAN as the native VLAN on trunk ports for all three services.

C. Use the Port Aggregation Protocol for negotiation.

D. Configure all the interfaces as access ports in the management VLAN.

A managed service is rolling out advanced wireless infrastructure to support an expanding organization with diverse device types. The implementation requires integration of dynamic endpoint profiling for secure access and device classification. According to the baseline deployment with ISE policy sets, the engineering group must enforce access parameters based on device category rules. Which configuration action must be taken to fulfill the initiative?

A. Create device-type groups.

B. Configure profiling groups.

C. Implement user ID groups.

D. Define endpoint group mapping.

Refer to the exhibit.]

An engineer is setting up a new WLC in a branch office. The IT security policy states that all management access must use encrypted protocols, administrators will connect remotely, and network scans will be run to check for any noncompliant management protocol exposure. Which action must the engineer take to achieve the required management access policy?

A. Permit only HTTP, Telnet, and SSH across all VLANs for 10.10.1.0/24.

B. Enable Telnet, SSH, and HTTPS across the management and guest interfaces.

C. Permit console access for 10.10.1.0/24 only with HTTP disabled.

D. Enable HTTPS and SSH, and disable HTTP and Telnet on the WLC.

Which role does a fabric edge node perform in a Cisco wireless fabric architecture?

A. Authenticating TLS connections for management

B. Enabling multicast snooping on edge switches

C. Terminating user data

D. Converting Layer 2 to Layer 3 addresses

Which CleanAir feature is used to avoid channels with interference from devices such as outdoor bridges and microwave ovens?

A. Persistent Device Avoidance

B. Spectrum Analysis

C. Air Quality Index

D. Channel Utilization

A persistent network issue is impacting connectivity for workstations in a training lab when connecting to a lab SSID. Wireless logs show clients never receive a DHCP offer when trying to obtain an IP address. The APs are operating in Local mode. Network monitoring systems indicate optimal signal quality and radio performance, VLAN assignments for the affected SSID have been configured, and all clients are affected. Which action resolves the issue?

A. Release or renew the client IP configuration.

B. Enable DHCP option 43.

C. Configure DHCP relay.

D. Disable multicast on the WLC.

An engineer must troubleshoot complex wireless performance issues in a large office which is using a Cisco 9176 AP. The engineer must analyze traffic patterns and identify potential sources of interference. The AP must capture all wireless frames in the air and send them to a remote protocol analyzer for detailed inspection. Client connectivity is not required from the AP during the troubleshooting window. Which CLI command must the engineer use on the WLC to enable the required AP mode for this purpose?

A. ap name office1st mode monitor

B. ap name office1st mode sniffer

C. ap name office1st mode local

D. ap name office1st mode rogue-detector

Which process allows continuous IP address retention in a wireless network during roaming?

A. static VLAN assignment policy

B. Layer 3 roaming

C. deferred probe response technique

D. redundant RF profile mapping

Which function does FRA use to optimize client experience and network coverage?

A. Monitoring on the physical interface level in the AP

B. Enhances roaming by redirecting the client to move to the appropriate AP

C. Implementation by local data path control

D. Dynamically adapts the roles of dual-band radios in an AP

Which Cisco Ultra-Reliable Wireless Backhaul process enables devices to establish a reliable connection with the next AP along their path before losing connectivity to the current one in a wireless network during roaming?

A. Open roaming

B. Fast client handoff

C. 802.11v high speed roaming

D. Make-before-break handover logic

A wireless controller is deployed at a branch location to facilitate secure client connectivity. A network engineer configures one WLAN using WPA2 Personal authentication and activates the preshared key method to align with company security policies. Which action must be taken to enable the client to connect to the WLAN?

A. Enter the preshared key at the WLAN security configuration prompt

B. Enable MAC filtering for security group assignment

C. Configure Active Directory integration for WLAN authentication

D. Import a client certificate for WPA2 authentication