Refer to the exhibit. The remote server is failing to receive the NetFlow data Which action resolves the issue?

A.

Modify the flow transport command transport udp 2055 to move under flow monitor profile.

B.

Modify the interlace command to Ip flow monitor FLOW-MONITOR-1 Input.

C.

Modify the udp port under flow exporter profile to Ip transport udp 4739.

D.

Modify the flow record command record v4_r1 to move under flow exporter profile.

Exhibit:

Which action resolves the authentication problem?

A.

Configure the user name on the TACACS+ server

B.

Configure the UDP port 1812 to be allowed on the TACACS+ server

C.

Configure the TCP port 49 to be reachable by the router

D.

Configure the same password between the TACACS+ server and router.

What does IPv6 Source Guard utilize to determine if IPv6 source addresses should be forwarded?

A.

ACE

B.

ACLS

C.

DHCP

D.

Binding Table

What does the PE router convert the Ipv4 prefix to within an MPLS VPN?

A.

VPN-IPv4 prefix combined with the 64-bit route distinguisher

B.

48-bit route combining the IP and PE router-id

C.

prefix that combines the ASN, PE router-id, and IP prefix

D.

eBGP path association between the PE and CE sessions

Refer to the exhibits. An engineer filtered messages based on severity to minimize log messages. After applying the filter, the engineer noticed that it filtered required messages as well. Which action must the engineer take to resolve the issue?

A.

Configure syslog level 2.

B.

Configure syslog level 3.

C.

Configure syslog level 4.

D.

Configure syslog level 5.

Drag and drop the MPLS concepts from the left onto the descriptions on the right.

Exhibit:

An engineer configured R2 and R5 as route reflectors and noticed that not all routes are sent to R1 to advertise to the eBGP peers. Which iBGP routers must be configured as route reflectors to advertise all routes to restore reachability across all networks?

A.

R1 and R4

B.

R1 and R5

C.

R4 and R5

D.

R2 and R5

Refer to the exhibit. The DHCP client is unable to receive an IP address from the DHCP server RouterB is configured as follows:
Interface fastethernet 0/0
description Client DHCP ID 394482431
Ip address 172 31 11 255 255.255 0
!
ip route 172.16.1.0 255 255 255.0 10.1.1.2
Which command is required on the fastethernet 0/0 interface of RouterB to resolve this issue?

A.

RouterB(config-if)#lp helper-address 172.31.1.1

B.

RouterBiconfig-ififclp helper-address 255.255 255 255

C.

RouterB(config-if)#lp helper-address 172.16.1.1

D.

RouterB(config-if)#lp helper-address 172.16.1.2

Refer to the exhibit.

Which two actions restrict access to router R1 by SSH? (Choose two.)

A.

Configure transport input ssh on line vty and remove sequence 30 from access list 100.

B.

Configure transport output ssh on line vty and remove sequence 20 from access list 100.

C.

Remove class-map ANY from service-policy CoPP

D.

Configure transport output ssh on line vty and remove sequence 10 from access list 199.

E.

Remove sequence 10 from access list 100 and add sequence 20 deny tcp any any eq telnet to access list 199

Refer to the exhibit. The engineer configured and connected Router2 to Router1. The link came up but could not establish a Telnet connection to Router1 IPv6 address of 2001:DB8::1. Which configuration allows Router2 to establish a Telnet connection to Router1?

A.

jpv6 unicast-routing

B.

permit ICMPv6 on access list INGRESS for Router2 to obtain IPv6 address

C.

permit ip any any on access list EGRESS2 on Router1

D.

IPv6 address on GigabitEthernet0/0

Refer to the exhibit.

When monitoring an IPv6 access list, an engineer notices that the ACL does not have any hits and is causing unnecessary traffic to pass through the interface Which command must be configured to resolve the issue?

A.

access-class INTERNET in

B.

ipv6 traffic-filter INTERNET in

C.

ipv6 access-class INTERNET in

D.

ip access-group INTERNET in

Refer to the exhibit. An engineer has successfully set up a floating static route from the BRANCH router to the HQ network using HQ_R1 as the primary default gateway When the g0/0 goes down on HQ_R1, the branch network cannot reach the HQ network 192.168.20.0/24. Which set of configurations resolves the issue?

A.

HQ_R3(config)# ip sla responder
HQ_R3(config)# ip sla responder icmp-echo 172.16.35.1

B.

BRANCH(config)# ip sla 1
BRANCH(config-ip-sla)# icmp-echo 192.168.100.2

C.

HQ R3(config)# Ip sla responder
HQ R3(config)# Ip sla responder Icmp-echo 172.16.35.5

D.

BRANCH(config)# Ip sla 1
BRANCH(config-ip-sta)# Icmp-echo 192.168.100.1